Author Topic: FT500 Vintage racer  (Read 1930 times)

FT500R

  • Full Member
  • ***
  • Posts: 160
Re: FT500 Vintage racer
« Reply #25 on: September 17, 2020, 10:06:17 am »
Got a new front fairing.
Made the fairing stay on the front already, have to tweak it a bit more but it is already pretty sturdy.
Will add some brackets to the sides to keep them in the correct position and from flapping around.
Also welded my linkpipe. Have to add a bracket to fix the linkpipe to the frame on the spot where the exhaust normally mounts and have to add a muffler hanger.

The windscreen on the pictures is one I had lying around. I will not use this one but it was more to get an idea of the looks.

hellblom

  • Newbie
  • *
  • Posts: 32
Re: FT500 Vintage racer
« Reply #26 on: September 21, 2020, 03:05:58 am »
What size tires do you have on this mr FT500?

FT500R

  • Full Member
  • ***
  • Posts: 160
Re: FT500 Vintage racer
« Reply #27 on: September 21, 2020, 07:09:28 am »
110/70/17 front
140/70/17 rear

FT500R

  • Full Member
  • ***
  • Posts: 160
Re: FT500 Vintage racer
« Reply #28 on: September 28, 2020, 04:01:50 am »
I've welded supports for the fairing so it is installed.
I made one support from the neck of the frame forward and 2 small tabs on the sides of the frame.

My welding isn't great but it's solid and when I will prepare for final painting of the frame I can grind the ugly bits down a bit.

I am very satisfied with the position and sturdiness of the fairing. It really hugs the bike nice and tight.


murdo

  • Full Member
  • ***
  • Posts: 110
Re: FT500 Vintage racer
« Reply #29 on: September 28, 2020, 04:08:45 am »
Looking good.  :)

hellblom

  • Newbie
  • *
  • Posts: 32
Re: FT500 Vintage racer
« Reply #30 on: September 28, 2020, 02:00:07 pm »
Well on the way! Looks good.

FT500R

  • Full Member
  • ***
  • Posts: 160
Re: FT500 Vintage racer
« Reply #31 on: October 13, 2020, 03:11:29 am »
Refurbished the front forks this weekend.
Not the first one I did and since this is not a cartridge style fork it was really easy.
Replaced all the seals and slider bushings as the seals were leaking and the bushings completely worn.
I removed the whole anti-dive system as this will lockup the forks when braking on a bumpy road (not something you want when riding on street circuits)

Also drilled some extra holes in the damping rods to prepare for cartridge emulators. I have gone for the YSS PD valves instead of the more well known racetech gold valves. Primarily because the YSS are actually obtainable in Europe and they are a lot cheaper.
I'll be running 15wt fork oil and will have to shorten the spring or the spacer to accomodate for the PD valve. Will post more on that whenever I get them.

The postal company has lost my package with the valves though but at least everything is prepared and they should be a quick drop in.
« Last Edit: October 13, 2020, 03:28:22 am by FT500R »

FT500R

  • Full Member
  • ***
  • Posts: 160
Re: FT500 Vintage racer
« Reply #32 on: October 16, 2020, 03:07:21 pm »
Fully welded the exhaust and slapped some cheap heat resistant paint on it. (I also drilled some holes in the header to weld in the inner tubes that got loose, seems to have worked)
After that I got some new sticky stuff for the FT.
I went with Bridgestone RS10s. Read a lot of good reviews about them, they were pretty affordable and were available as a set in the sizes I wanted. Really happy with them. I got 110/70/17 for the front and 140/70/17 for the rear.

For the front forks I came across these things:

These fit on the forks instead of the current caps. I would loose the air valves and with that the possibility to pressurize the forks but would gain pre-load adjustment. Anyone any experience with something similar?

murdo

  • Full Member
  • ***
  • Posts: 110
Re: FT500 Vintage racer
« Reply #33 on: October 16, 2020, 04:15:30 pm »
I used the adjustable top caps on one of my CBR250's and found they made a noticable difference.